1. TI-5000 Series | PAI: Polyamide-imide | Disengaging latch TI grade | Gear TI grade

Characteristics

1. (1) The TI-5000 Series demonstrates a superior balance of heat resistance and strength.
   Its non-reinforced strength at 250°C rivals that of POM at room temperature.
2. (2) The superior wear resistance of the TI-5000 Series prevents any damage to itself or to other materials.
   → Damage to the photosensitive drum heat roll is miniscule.
3. (3) This series demonstrates superior creep property.
   → Deformations are rare, and jammings are minimal.
4. (4) This series demonstrates superior dimensional stability.
   → The linear expansion coefficient is minimal, and precision is high.

The TI-5000 Series "exceeds the performance of traditional engineering plastics in almost all aspects."

Superior Balanced Physical Properties and Optimal for Heat-Resistant Gears

The TI-5000 Series boasts superior heat resistance (continuous use temperature of 250°C), heat distortion resistance (deflection temperature under load of 279°C), mechanical properties (especially tensile strength and shock resistance), fatigue resistance, flame retardance, friction and wear resistance, and stress crack resistance.

Characteristics

1. (1) The TI-5000 Series demonstrates a superior balance of heat resistance and strength.
   → Its strength lends itself to preventing cracks in gear tips or welding.
2. (2) It demonstrates high strength even without reinforcement from glass fibers as well as superior abrasion resistance.
   → This property prevents any damage to itself or to other materials (for example, contact gears or internal shafts)
3. (3) This series demonstrates superior dimensional stability.
   → The linear expansion coefficient is minimal, and precision is high.

The TI-5000 Series “exceeds the performance of traditional engineering plastics in almost all aspects.”

2. TI-200 Series (PPS-based) Gear TI grade

A Series with High Heat Resistance and Strength for Those Looking for a Low-Cost Option!

The TI-200 Series is based on PPS resin, which offers superior heat resistance and flame retardancy, strengthened with special fibers. Its favorable moldability lends itself well for manufacturing with reliably high accuracy. The combination of high-strength grade TI-250A and sliding grade TI-200C not only gives this series low self-abrasion, but it also lowers the abrasion with other materials under extreme usage conditions of high temperature and high torque.

Gear Grade Properties Table:

Property	Testing Method	Unit	250A	200C-H02	5013	5031
Specific gravity	D792		1.67	1.67	1.40	1.45
Water absorption (24 Hrs)	D570	%	0.02	0.02	0.33	0.28
Tensile strength	D638	MPa	200	165	186	157
Tensile elasticity	D638	%	2.3	1.9	15.0	8.0
Bending strength	D790	MPa	260	210	235	196
Bending elasticity	D790	GPa	12.7	10.5	4.9	6.4
Izod impact strength (notched)	D256	J/m	130	105	127	59
Deflection temperature under load (1.82 MPa)	D648	°C	>260	>260	>278	>279
Fiber reinforcing			Reinforced (PPS)	Reinforced (PPS)	Non-reinforced (PAI)	Non-reinforced (PAI)
			High strength	High strength Wear resistance	Ultrahigh strength Wear resistance	Ultrahigh strength Wear resistance

* This is a table of representative examples based on values measured from testing carried out under specific conditions.

3. TI-200/7000 Series (PPS/PEEK-based) Disengaging Latch TI grade

Coating Technology Imbibed with Noncohesive Toner that Offers High Heat Resistance and Strength

The TI-200 Series is based on PPS resin, which offers superior heat resistance and flame retardancy, strengthened with special fibers. Its favorable moldability lends itself well for manufacturing with reliably high accuracy. In addition, the series has a superior application to the PTFE coating which makes the toner non-cohesive. The TI-7000 Series is based on PEEK, a resin whose heat resistance is better than that of TI-200, and reinforced by special fibers. Because of this, TI-7000 has a superior application to the PFA coating which improves toner non-cohesiveness much further.

Disengaging Latch Grade Properties Table:

Property	Testing Method	Unit	240A	7200	8000	7500	5013	550F
Specific gravity	D792		1.73	1.47	1.70	1.75	1.40	2.17
Water absorption (24 Hrs)	D570	%	0.02	0.02	0.05	0.08	0.33	0.03
Tensile strength	D638	MPa	180	98	120	170	186	32
Tensile elasticity	D638	%	3.0	3.5	2.1	3.0	15.0	410
Bending strength	D790	MPa	270	127	190	280	235
Bending elasticity	D790	GPa	18.0	6.9	12.9	14.0	4.9
Izod impact strength (notched)	D256	J/m	45	25		30	127	Nondestructive
Deflection temperature under load (1.82 MPa)	D648	°C	>260	>260	>290	>290	278
Coating			PTFE	PTFE	PFA	PFA	PTFE	None
Application example(s)			Fixing pawl	Fixing pawl	Fixing pawl	Fixing pawl	Fixing pawl Drum pawl	Fixing pawl

* This is a table of representative examples based on values measured from testing carried out under specific